亚洲国产丝袜av激情区精品_日韩美女无毛黄片_国产在线观看91福利丝袜_国产精品先锋资源站先锋影院_欧美日韩一区免费_国产日韩欧美福利_成人在线性爱视频_国产v综合v亚洲欧美久久_亚洲最大的毛片基地_九九成人午夜免费视频

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

500 tons hydraulic press cylinder Sold to Canada

Release time:2023-11-26 09:49:39 Hits: Current position: Home > News

This article mainly introduces:

Canada hydraulic cylinder,500 tons hydraulic press cylinder manufacturer,500 tons hydraulic press cylinder

Canada 500 tons hydraulic press cylinder

(Canada 500 tons hydraulic press cylinder,produced by Hengyu Hydraulic Cylinder Factory)

500 tons hydraulic press cylinder are widely used in Canada,because of long service life,smooth movement,no need for deceleration device.So our company has designed 500 tons hydraulic press cylinder for customers from Canada.

Introduction to 500 tons hydraulic press cylinder:

500 tons hydraulic press cylinder diameter, rod diameter, stroke determination: Choose national standards or other standards 500 tons hydraulic press cylinder, avoid the selection of non-standard size, otherwise the difficulty of processing and manufacturing costs will be increased. The length of the 500 tons hydraulic press cylinder guide is determined by the length of the stroke. Check the strength of 500 tons hydraulic press cylinder, piston rod, screw, etc. according to the working pressure or load. At the same time, working pressure, ambient temperature, working medium and running speed are also the key to selecting seals.

The 500 tons hydraulic press cylinder is not the same as the 500 tons hydraulic press cylinder, because the pressure of the pneumatic system is generally within the range of 0.2-1.0Mpa, the 500 tons hydraulic press cylinder can not be used as a high-power power component, but the 500 tons hydraulic press cylinder can be used as a relatively large power component, or the 500 tons hydraulic press cylinder system can be used.

When installing the piston rod, it is necessary to ensure that the direction of the connecting head at the top of the piston rod should be consistent with the direction of the 500 tons hydraulic press cylinder head adn the earring (or the middle hinge shaft), and ensure the straightness of the whole piston rod during the advance and return process to prevent the phenomenon of rigid interference and causing unnecessary damage.

Piston 500 tons hydraulic press cylinder is widely used in hydraulic transmission. When the 500 tons hydraulic press cylinder works, it mainly delivers hydraulic oil alternately to both sides of the piston in the 500 tons hydraulic press cylinder, and uses the pressure difference of hydraulic oil on both sides of the piston to realize the reciprocating movement of the piston. If you want to speed up the forward speed of the piston, the return oil in the 500 tons hydraulic press cylinder can be controlled by the valve and directly input into the inlet pipe to participate in the work of the piston to achieve rapid movement of the piston, but the thrust of the piston is reduced much.

Answers to some questions about 500 tons hydraulic press cylinder:

Slide weight 35 kg exit stroke 55mm, is it suitable to use 40 cylinder diameter cylinder?
The maximum output force of the 40-bore hydraulic cylinder can reach 2 tons, and whether it can be used depends on the use scenario. In addition, the problem of mechanism stuck has nothing to do with the size of the power source, and reasonable structural design and good machining and assembly accuracy are the key.

What are the differences between hydraulic cylinder and pneumatic cylinder, what are their advantages and disadvantages?
Hydraulic Cylinder: small body and large force, constant speed and variable speed (easy to change), the adjustment of output is also convenient, and the degree of freedom of transmission is high. However, maintenance costs and installation costs are high, and there is the trouble of mild oil pollution. Pneumatic Cylinder: easy to control, low price, easy access to energy. But the force is small, and can not achieve the effect of stable speed. The gas-liquid pressurized cylinder has the advantages of both of the above: environmental protection and energy saving, easy control, and simple adjustment. However, the output of the trip has certain restrictions, so it is more suitable for short trips, large output, but also environmental protection and energy saving and low configuration of the occasion. Because the pressure used in the pneumatic system is generally in the range of 0.2-1.0Mpa, the cylinder is not suitable for high power component.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP